header-image

Design Controls for Drug - Device Combination Products - Live Online Training

5/6 October 2022

Seminar-Nr. 19389

Referent:innen

Torsten Kneuss

Torsten Kneuss

Bayer

Note: All times mentioned are CET.

Zielsetzung

This Live Online Training provides a comprehensive overview of the technical and regulatory requirements for the development and maintenance of drug-device combination products (with a focus on EU & US).

Participants will learn and understand
  • the basics – distinctions between drugs, devices and ‘combination products’,
  • the current applicable regulations, standards and guidelines related to the design and development of combination products and how to be compliant with those requirements
  • the key elements of Design Controls, Risk Management and Usability Engineering.
Case Studies are an integral part of the course Programme.

Hintergrund

More than half of the TOP20 drug products on the market include at least one device constituent part and are therefore considered Drug-device combination products. Drug-Device combination products are specifically regulated in the US. However, there is also an increasing oversight by regulatory authorities in the EU. GMP compliant development and life-cycle management are, therefore, essential for obtaining and maintain a marketing authorization for such products.

What is a Combination Product?

“Combination Product”, as per 21 CFR Part 3.2(e), is a term defined by the FDA to cover products which consist of two or more components (i.e., drug, biologic, device) regulated under different regulations. The FDA differentiates between three basic types of combination products:
  • Single-entity combination products,
  • Co-packaged combination products,
  • Cross-labeled combination products.
Beyond these basic types also combinations of those basic types are possible.

During the past years, FDA established regulations and guidances for Combination Products, which further clarify what Combination Products are and which rules apply to such combinations.

21 CFR Part 4, along with the final guidance “Current Good Manufacturing Practice (cGMP) Requirements for Combination Products”, provides guidance on applicable quality requirements for combination products.
 
One essential requirement is to apply Design Controls as defined in 21 CFR Part 820.30 to the combination product as a whole. Design Controls are a set of quality practices and procedures to control the design process to assure that the combination product meets the user needs, intended uses and specified requirements. Design Controls are described in ISO 13485 (applicable for Medical Devices), in ISO 15378 (applicable to primary packaging materials) and even in the general standard for quality management system ISO 9001

In the EU, so far, there has been no equivalent term to “Combination Product”, a product is either considered a Medical Device or a Medicinal Product. Medical devices have to comply with the EU Medical Device Regulation (MDR). Even though the term Combination Product does not exist, also in EU, the Design Controls apply to the so-called single-integral products, which are similar to single-entity combination products as defined in the US.

Also shared in EU and US is the requirement to apply Risk Management to those products. The respective standard ISO 14971 has been revised in 2019. The course will consider the recent changes and provides guidance on how to apply Risk Management to drug-device combination products.
 
And lastly, also Usability Engineering, also known as Human Factors Engineering, needs to be considered in the Design and Development of combination products. The recent increase in attention to this topic has brought many manufacturers into difficulties as they aim to prove high levels of intuitive use, use safety and efficacy of the drug delivery system as a whole - for a Combination Product it is no longer just about the drug. Again, regulation, directives, guidance, standards and review expectations continue to evolve in this area.

This Live Online Training focuses on design controls as applicable to various combinations of drugs and biologics with devices. The course intends to set a solid basic understanding of the application on Design Controls as  well as on the topics of Risk Management and Usability Engineering. Beyond the basic understanding, the course also aims to offer some practical experiences with the different elements to be considered.

Zielgruppe

This Live Online Training is designed for all scientists, engineers, managers and executives from Pharmaceutical and Biotech Development Units, including Device Development, Packaging Development, Quality Assurance, Regulatory Affairs, Marketing, and Project Management, who are involved in the development, industrialization and control of Drug-Device Combination Products.

Technical Requirements

We use Webex Events for our live online training courses and webinars. At https://www.gmp-compliance.org/training/online-training-technicalinformation you will find all the information you need to participate in our events and you can check if your system meets the necessary requirements to participate. If the installation of browser extensions is not possible due to your rights in the IT system, please contact your IT department. Webex is a standard nowadays and the necessary Installation is fast and easy.

Programm

Design Controls for Drug - Device Combination Products - Live Online Training

Gesamtes Programm als PDF herunterladen

Programme Day 1
 
Design Controls – An Introduction
  • Purpose of Design Controls / Usability Engineering / Risk Management
  • Drug Development vs. Device Development vs. Combination Product Development
  • Development vs. Transfer vs. Industrialization
  • Processes required
Design and Development Planning
  • Definition of development scope
  • Target Product Profile - How to determine the scope?
  • Design Reviews
  • Scope of DC
  • Segregation Device vs. Pharma company
EU Requirements for Single-Integral Products
  • How to demonstrate conformance with Annex I?
  • Setup of technical documentation
  • General safety & performance requirements
Introduction to Usability Engineering
  • IEC 62366-1
  • How to determine user needs, user preference, use specification etc.
Q&A Session 1

Introduction to Risk Management
  • ISO 14971: Terms/definitions, process, relevance for design controls
  • EU and US requirements
  • Determine Known Use Problems
Risk Management (Example)
  • How to determine risk mitigations for design Inputs
  • Update of risk management during development
  • Documentation of RM activities / RMF
  • Preparation of post-market surveillance / PMS planning
FDA Regulatory Expectations on Drug - Device Combinations
  • Types of Combination Products and impact on GMP Requirements
  • Which Medical Device Quality Systems are required and at which facilities are they required to be implemented?
  • Expectations for Clinical Phases and for Submissions
  • Post Marketing expectations
Case Study I: Pre-filled Syringes

Q&A Session 2
 
Programme Day 2
 
Design Input
  • From user needs and other stakeholder needs to design Input
  • How to integrate results from UE, RM
  • How to ensure „open-ended“ development
  • Requirements for engineering techniques
Design Output
  • Development activities
  • Definition of design outputs (Specifications)
Design Verification
  • Design verification activities
  • How to consider verification during design Input
  • What to do if verification fails?
Q&A Session 3

Design Validation / Usabality Engineering Part 2
  • Design validation approaches
  • Planning, setup and conduct of summative studies
  • Documentation of the UE activities / UEF
  • HF/UE Report as required by FDA
Design Transfer
  • Design Transfer - Why and how?
  • DMR setup
Case Study II: Autoinjector Development
(Some considerations when utilising syringes in autoinjectors)

Q&A Session 4
 

Dieses Seminar/Webinar kann nicht gebucht werden. Alternative Termine für dieses Seminar/Webinar und ähnliche Veranstaltungen finden Sie in der Übersicht nach Thema..

Für viele Seminare und Webinare gibt es auch Aufzeichnungen, die Sie jederzeit bestellen und anschauen können. Diese Aufzeichnungen finden Sie in einer themensortierten Liste.

Oder senden Sie uns Ihre Anfrage einfach über das folgende Kontaktformular.

* auch unkompliziert per Kreditkarte bezahlbar
American Express Visa Mastercard

icon
Weitere Termine vor Ort
Weitere Termine vor Ort nicht verfügbar
icon
Weitere Termine online
Weitere Termine online nicht verfügbar
icon
Aufzeichnung nicht verfügbar

Haben Sie noch Fragen?

Wir stehen Ihnen für weitere Auskünfte gerne zur Verfügung.
Tel.: +49 6221 84 44 0
E-Mail: info@concept-heidelberg.de

Frau mit Headset

Zurück

Teilnehmerstimmen - das sagen andere über unsere Seminare:

Guter, breit gefächerter Überblick mit interessanten Verknüpfungen zur Praxis,
welche die Theorie super veranschaulicht.”
Marina Kicoranovic, Labor Hartmann GmbH
GMP/Basis-Einstiegsschulung (B 14), September 2023

Die Referenten waren sehr gut! Sie haben sehr klar gesprochen, nur sehr wenige englische Begriffe
verwendet (super) und waren sehr praxisbezogen.”
Astrid Gießler, Regierungspräsidium Karlsruhe
Live Online Seminar - Basiskurs Computervalidierung & Datenintegrität im GxP Umfeld (B 3), Juni 2023

Sehr guter Bezug zur Schulung für einen GMP-Anfänger. Habe mich sehr gut abgeholt gefühlt.”
Dr. Harald Werner, Infraserv GmbH & Co. Höchst KG
GMP-Basisschulung (B 1), Juni 2023

NEWSLETTER

Bleiben Sie informiert mit dem GMP Newsletter von Concept Heidelberg!

GMP Newsletter

Concept Heidelberg bietet verschieden GMP Newsletter die Sie auf Ihren Bedarf hin zusammenstellen können.

Hier können Sie sich kostenfrei registrieren.

Kontakt

Kontaktieren Sie uns

Haben Sie Fragen?

Concept Heidelberg GmbH
Rischerstraße 8
69123 Heidelberg

Tel. :+49622184440
Fax : +49 6221 84 44 84
E-Mail: info@concept-heidelberg.de

zum Kontaktformular